Forskjell mellom versjoner av «Rolling stock/Supplementary information and regulations»

[ukontrollert revisjon][ukontrollert revisjon]
m (Functional and technical specification related to the electric power supply: midlertidig løsning for banestrømforsyning)
m (Axle load and wheel load)
Linje 14: Linje 14:
==== Load conditions and weighted mass ====
==== Load conditions and weighted mass ====
==== Axle load and wheel load ====
==== Axle load and wheel load ====
Maximum acceptable axle load is dependent on speed and class of superstructure. Permitted speed and axle load versus classes of superstructure is given in [[Overbygning/Prosjektering/Generelle tekniske krav#Overbygningsklasser|Overbygning/Prosjektering/Generelle tekniske krav]].
Lines of superstructure class b, with low traffic load, are under some circumstances permitted an axle load of 22,5 tons for freight trains with maximum speed of 60 km/h. The total traffic load is not to exceed 2 million gross tons (MGT). Out of this total, the maximum traffic load for freight train axle loads larger than 20,5 tons is 1 MGT.
=== Joining technology ===
=== Joining technology ===
=== Lifting and jacking ===
=== Lifting and jacking ===

Revisjonen fra 26. jun. 2012 kl. 15:00


1 General documentation

1.1 General documentation

1.2 Maintenance instructions and requirements

1.2.1 Maintenance instructions

1.2.2 The maintenance design justification file

1.3 Instructions and documentation for operation

1.3.1 Instructions for operation in normal and degraded modes of the vehicle

1.4 Track-side tests of the complete vehicle

2 Structure and mechanical parts

2.1 Vehicle structure

2.1.1 Strength and integrity

2.1.2 Load capability Load conditions and weighted mass Axle load and wheel load

Maximum acceptable axle load is dependent on speed and class of superstructure. Permitted speed and axle load versus classes of superstructure is given in Overbygning/Prosjektering/Generelle tekniske krav.

Lines of superstructure class b, with low traffic load, are under some circumstances permitted an axle load of 22,5 tons for freight trains with maximum speed of 60 km/h. The total traffic load is not to exceed 2 million gross tons (MGT). Out of this total, the maximum traffic load for freight train axle loads larger than 20,5 tons is 1 MGT.

2.1.3 Joining technology

2.1.4 Lifting and jacking

2.1.5 Fixing of devices to car body structure

2.1.6 Connections used between different parts of the vehicle

2.2 Mechanical interfaces for end coupling or inner coupling

2.2.1 Automatic coupling

2.2.2 Characteristic of rescue coupling

2.2.3 Screw couplings

2.2.4 Buffing, inner coupling and draw gear components

2.2.5 Buffer marking

2.2.6 Draw hook

2.2.7 Gangways

2.3 Passive safety

3 Track interaction and gauging

3.1 Vehicle gauge

3.1.1 Specific case

3.2 Vehicle dynamics

3.2.1 Running safety and dynamics

3.2.2 Equivalent conicity, wheel profile and limits

3.2.3 Track loading compatibility parameters

3.2.4 Vertical acceleration

3.3 Bogies/running gear

3.3.1 Bogies

3.3.2 Wheel set (axle + wheels)

3.3.3 Wheel

3.3.4 Wheel/rail interface (including wheel flange lubrication and sanding)

3.3.5 Bearings on the wheel set

3.3.6 Minimum curve radius to be negotiated

3.3.7 Rail guard

3.4 Limit of maximum longitudinal positive and negative acceleration

4 Braking

4.1 Functional requirements for braking at train level

4.2 Safety requirements for braking at train level

4.2.1 Traction/braking interlocking

4.3 Brake system

4.4 Brake command

4.4.1 Emergency braking command

4.4.2 Service braking command

4.4.3 Direct braking command

4.4.4 Dynamic braking command

4.4.5 Parking braking command

4.5 Brake performance

4.5.1 Emergency braking

4.5.2 Service braking

4.5.3 Calculations related to thermal capacity

4.5.4 Parking brake

4.6 Braking adhesion management

4.6.1 Limit of wheel rail adhesion profile

4.6.2 Wheel slide protection system

4.7 Braking force production

4.7.1 Friction brake Brake blocks Brake discs Brake pads

4.7.2 Dynamic brake linked to traction

4.7.3 Magnetic track brake

4.7.4 Eddy current track brake

4.7.5 Parking brake

4.8 Brake state and fault indication

4.9 Brake requirements for rescue purposes

5 Passenger-related items

5.1 Access

5.1.1 Exterior doors

5.1.2 Interior doors

5.1.3 Clearways

5.1.4 Steps and lighting

5.1.5 Floor height changes

5.1.6 Handrails

5.1.7 Boarding aids

5.2 Windows

5.3 Toilets

5.4 Passenger information

5.4.1 Public address system

5.4.2 Signs and information

5.5 Seats and specific PRM arrangements

5.6 Specific passenger-related facilities

5.6.1 Lift systems

5.6.2 Heating, ventilation and air condition systems

5.6.3 Other

6 Environmental conditions and aerodynamic effects

6.1 Impact of the environment on the vehicle

6.1.1 Environmental conditions impacting on the vehicle Altitude Temperature Humidity Rain Snow, ice and hail Solar radiation Chemical and particulate matter

6.1.2 Aerodynamic effects on the vehicle Crosswind effects Maximum pressure variation in tunnels

6.2 Impact of the vehicle on the environment

6.2.1 Chemical and particulate emissions Toilet emissions Exhaust gas emissions

6.2.2 Limits for noise emissions Exterior noise impact Stationary noise impact Starting noise impact Pass-by noise impact

6.2.3 Limits for aerodynamic loads impact Head pressure pulses Aerodynamic impact on passengers/materials on the platform Aerodynamic impact on track workers Ballast pick-up and projection onto neighbouring property

7 External warning, marking functions and software integrity requirements

7.1 Integrity of software employed for safety-related functions

7.2 Visual and audible vehicle identification and warning functions

7.2.1 Vehicle marking

7.2.2 External lights Headlights Marker lights Tail lights Lamp controls

7.2.3 Warning horn Warning horn tones Warning horn sound pressure levels Warning horns, protection Warning horns, control Warning horns verification of sound pressure levels

7.2.4 Brackets

8 Onboard power supply and control systems

8.1 Traction performance requirements

8.1.1 Residual acceleration at max speed

8.1.2 Residual traction capability in degraded mode

8.1.3 Traction wheel/rail adhesion requirements

8.2 Functional and technical specification related to the interface between the vehicle and the energy subsystem

8.2.1 Functional and technical specification related to the electric power supply

As a temporarily solution supplementary information and regulation for power supply is found in Technical specification 02: Requirements on rolling stock in Norway and Sweden regarding EMC with the electrical infrastructure and coordination with the power supply and other vehicles. The specification includes information about the different chapters below in this section together with guidelines for testing of the different requirements. For #Harmonic characteristics and related over-voltages on the overhead contact line the specification contains the requirements as a part of the compatibility prosess. For the other chapters, the valid requirements are found in the Annex to the Railway Vehicle Regulations. Power supply Impedance between pantograph and wheels Voltage and frequency of overhead contact line power supply Energy recuperation Maximum power and maximum current that is permissible to draw from the overhead contact line Power factor System energy disturbances Harmonic characteristics and related over-voltages on the overhead contact line

The following requirements are still valid as a part of the compatibility study to be performed:

  • P3: Line voltage distortion (chapter
  • P8: Low frequency power oscillations (chapter
  • P9: Electrical resonance stability (chapter
  • P10: Current harmonics (chapter Effects of DC content in AC supply Electrical protection

8.2.2 Pantograph functional and design parameters Pantograph overall design Pantograph head geometry Pantograph static contact force Pantograph contact force (including dynamic behaviour and aerodynamic effects) Working range of pantographs Current capacity Arrangement of pantographs Insulation of pantograph from the vehicle Pantograph lowering Running through phase separation sections Running through system separation sections

8.2.3 Contact strip functional and design parameters Contact strip geometry Contact strip material Contact strip assessment Detection of contact strip breakage Current capacity

8.3 Electrical power supply and traction system

8.3.1 Energy consumption measurement

For vehicles that will operate in several geographical price and/or network areas on the national rail network, the energy measurement system shall be equipped with a location function according to TSI LOC&PAS Alternatively will the Jernbaneverket charge the energy based on key figures of consumption and regeneration per gross tonn kilometer according to Jernbaneverkets standardvilkår for avregning av 16 2/3 Hz energi.

8.3.2 Main electrical circuit configuration

8.3.3 High voltage components

8.3.4 Earthing

8.4 Electromagnetic compatibility

8.4.1 Electromagnetic compatibility within the onboard electrical power supply and control system

8.4.2 Electromagnetic compatibility with the signalling and telecommunications network

8.4.3 Electromagnetic compatibility with other vehicles and with the trackside part of the railway system

8.4.4 Electromagnetic compatibility with the environment

8.5 Protection against electrical hazards

8.6 Diesel and other thermal traction system requirements

8.7 Systems requiring special monitoring and protection measures

8.7.1 Tanks and pipe systems for flammable liquids

8.7.2 Pressure vessel systems/pressure equipment

8.7.3 Steam boiler installations

8.7.4 Technical systems in potentially explosive atmospheres

8.7.5 Ionisation detectors

8.7.6 Hydraulic/pneumatic supply and control systems

9 Staff facilities, interfaces and environment

9.1 Driver’s cab design

9.1.1 Cab design Interior layout Desk ergonomics Driver’s seat Means for the driver to exchange documents Other facilities to control operation of the train

9.1.2 Access to driver’s cab Access, egress and doors Driver’s cab emergency exits

9.1.3 Windscreen in driver’s cab Mechanical characteristics Optical characteristics Equipment Front visibility

9.2 Working conditions

9.2.1 Environmental conditions Heating, ventilation and air condition systems in driver cabs Noise in driver cabs Lighting in driver cabs

9.2.2 Others

9.3 Driver/machine interface

9.3.1 Driver/machine interface Speed indication Driver display unit and screens Controls and indicators

9.3.2 Driver supervision

9.3.3 Rear and side view

9.4 Marking and labelling in driver cabs

9.5 Equipment and other facilities onboard for staff

9.5.1 Facilities onboard for staff Staff access for coupling/uncoupling External steps and handrails for shunting staff Storage facilities for use by staff Other facilities

9.5.2 Staff and freight access doors

9.5.3 Onboard tools and portable equipment

9.5.4 Audible communication system

9.6 Recording device

9.7 Vacant

9.8 Remote control function

10 Fire safety and evacuation

10.1 Fire safety

10.1.1 Fire protection concept Classification of vehicle/fire categories

10.1.2 Fire protection measures General protection measures for vehicles Fire protection measures for specific kinds of vehicles Protection of driver’s cab Fire barriers Material properties Fire detectors Fire extinction equipment

10.2 Emergency

10.2.1 Passenger emergency exits

10.2.2 Rescue services’ information, equipment and access

10.2.3 Passenger alarm

10.2.4 Emergency lighting

10.3 Additional measures

11 Servicing

11.1 Train cleaning facilities

11.1.1 Train external cleaning facilities

11.1.2 Train internal cleaning

11.2 Train refuelling facilities

11.2.1 Waste water disposal systems

11.2.2 Water supply system

11.2.3 Further supply facilities

11.2.4 Interface to refuelling equipment for non-electric rolling stock

12 Onboard control command and signalling

12.1 Onboard radio system

12.1.1 Non-GSM-R radio system

12.1.2 GSM-R compliant radio system Text messages Call forwarding Broadcast calls Cab-radio related requirements Network selection by external trigger General purpose radio-related functions Primary controller’s MMI functionality Use of hand portables as cab mobile radio Capacity of onboard GSMR GSM-R-ETCS interface Interconnection and roaming between GSM-R networks Border crossing GPRS and ASCI Interface between rolling stock driver’s safety device, vigilance device, and GSM-R onboard assembly Test specification for mobile equipment GSM-R Directed/automatic network selection Registration and deregistration GSM-R version management

12.2 Onboard signalling

12.2.1 National onboard signalling systems

12.2.2 Compatibility of signalling system with the rest of the train

12.2.3 Compatibility of rolling stock with track infrastructure Relation between axle distance and wheel diameter Metal free space around wheels Metal mass of a vehicle

12.2.4 ETCS cab signalling system Awakening Train categories Performance requirements for onboard GSM-R equipment related to quality of service Use of ETCS modes ETCS requirements when vehicle is driven from outside the cab Level crossing functionality Braking safety margins Reliability — Availability — Safety requirements Marker boards Ergonomic aspects of the DMI ETCS values of variables controlled outside UNISIG — Manual KM conformance requirements Requirements for pre-fitting ETCS onboard equipment ETCS version management Specification of ETCS variables RBC — RBC interface Additional requirements on locomotives and multiple units Functionality and interfaces of staff protection systems to the signalling system Interface with service brake

13 Specific operational requirements

13.1 Specific items to place onboard

13.2 Occupational health and safety

13.3 Lifting diagram and instructions for rescue

14 Freight-related items

14.1 Design, operation and maintenance constraints for the transport of dangerous goods

14.2 Specific facilities for the transport of freight

14.3 Doors and loading facilities